CONTENTSFOREWORD...OPERATION...NOMENCLATURESingle frame shooting (S)...PRE
Insert the camera plug with the A symbol on the plug pointing upwards into the remote terminal of the camera. Then screw the threaded ring into the
Insert the bracket between I the tripod head and the camera. Then, screw the tripod’s lock nut firmly to secure the assembly.2.Insert the receiver int
I'ou should also replace catteries If the LED starts clinking after it lights up.Notes:• Power/channel selector switch setting on the receiver m
Positioning the transmitter and receiverWhen positioning the transmitter and receiver, check the foliowing to ensure effective transmission.• There
• The receiver’s reception sensor faces away from the sun.> When using the ML-3 at the same time as video recording equipment, do not point the vid
Distance range Channel selector settingSet each corresponding transmitter/receiver pair to the same channel. Up to two IVIL-3 sets can be used in the
Camera settingsBe sure to adjust the camera settings before operation.Recommended camera settings are:Focus modes: C or MFilm advance modes: OiLorai”E
Single frame shooting (S)Set shooting mode selector on the transmitter to S.• If the camera’s focus mode is set to S, the camera may not focus corr
) Fully depress the transmission button.> .The reception indicator LED will light up for a moment and one picture will be taken. Avoid changing the
FOREWORD--------------------Thank you for purchasing the Nikon Moduiite Remote Control Set ML-3. The Nikon ML-3 combines a transmitter and receiver fo
Continuous frame shooting (C)Set the transmitter’s 1 shooting mode seiector to C.• if the camera’s focus mode is set to S, the camera may not focus c
3 Fully depress the transmission button. Pictures are taken• continuously as long as the transmission button is fully depressed. The reception indica
Delay triggeringIn this mode, shutter release occurs approx. 3 seconds after you fully depress the transmission button so you can include yourself in
Point the transmitter in the direction of the . • reoeption sensor and lightly press the transmission button. The monitor light will light up for a mo
Auto triggeringIn this mode, the shutter is reieased when the subject enters the area directiy between the transmitter and the receiver, without the t
I Set the shooting mode , selector to DELAY/TEST.Auto triggering operationI Point the transmitter toward • • the receiver and block infrared ray
Set the transmitter's shooting mode to S or C.Set the receiver’s power/channei selector switch to CH 1 or CH2.Set camera, transmitter and r
' Adjust focus manually * • according to estimated subject position between the transmitter and receiver.• To ensure clearly focused plcture(s):
Transmitter, receiver and camera indicationsTransmitterReceiverCameraChannel selectorShooting modeTransmission button selector/Monitor lightLEDCHI orC
WIRELESS FLASH OPERATIONWhen preparing for shooting, turn Speedlight power on by lightly pressing the transmission button. For extended operation, spe
NOMENCUTURETRANSMIUER© Shooting mode selector: S for single-frameshooting, C for continuous shooting, DELAY/TEST for delaying shutter release or check
Connect the receiver’s camera plug to camera’s remote terminal.Set the Speedlight’s power • switch to STBY.Start shooting. For details on flash sh
TIPS ON CAREplace.• Avoid using where strong magnetic or electric waves are discharged (e.g., near TV tower). Malfunction may result.32
Cleaning:• Clean with a soft, clean cloth or blower brush.• After use near the sea, wipe equipment first with a water-moistened soft cloth. Do not use
SPECIFICATIONSTransmitter and receiverModulation system Infrared communicationApprox, 8m (26.2 ft.)along the optical axis Approx, 6m (19.7 ft.) with a
ReceiverPower/channelswitchNumber of input channels Power sourceRemote cord Shoe footBattery power checkCompatibility with ML-2DimensionsWeightCHI orC
RECEIVER© Camera plug ® Remote cord® Mounting foot lock screw: Be sure to tighten firmly when attaching receiver to the camera or bracket ® Power/chan
ACCESSORIESBracket (optional): For use when receiver cannot be mounted on the camera.
Close the battery lid by • sliding it back into place.Set power switch to ON. • If the monitor light comes on for a moment, batteries have sufficie
If it blinks, batteries may be weak.** Only with the channel selector set to CHI or CH2.If it does not come on, check battery instaiiation or replace
ReceiverConnecting the receiver to a camera1 Using gentle finger pressure, loosen the mounting foot lock screw as far as it goes without applying fo
Comentários a estes Manuais